Ford Scorpio engine diagram

Here are general Ford Scorpio еngine diagrams for various Ford Scorpio models: Ford Scorpio Turnier, Ford Scorpio Hatchback, Ford Escort... Ford Scorpio engine diagram - engines: 2.9 i 4x4 (145 Hp), 2.9 i (145 Hp), 2.8 i (150 Hp), 2.4 i KAT (125 Hp), 2.5 TD (116 Hp)...

Ford Scorpio engine with intermediate injection of fuel in a combustion chamber, four-cycle, four-cylinder, water cooling, has a cam shaft in the cylinder block, is established is longitudinal ahead of the car. The cylinder block is cast from pig-iron. A bent shaft with fixing from an axial movement persistent half rings which are established on the central main bearer. The cam shaft rotates in three bearing parts. The cylinder block head is made of an aluminium alloy. Each valve is closed by two springs. Turbo-compressor Carret AiRtsearch T03 is established since 1988 and put in action by energy of exhaust gases. On one shaft with the turbine there is a compressor. The turbo engine feed system same, as well as at the usual engine.

Ford Scorpio engine V6 with the top valve arrangement and the bottom arrangement of a cam shaft in the engine basic block, which is put in action through drive from a bent shaft (engine V6 2,8) or a chain (engines V6 2,4 and 2,8 l). Cylinder block heads are established in such a manner that the intake manifold is located between them, and exhaust manifolds from outer sides of collectors. The cylinder block is made of pig-iron. Buckets from an aluminium alloy, connected to a bent shaft by means of connecting rods. The bent shaft rotates in four bearings. Lubricant under pressure is carried out by means of the oil pump.

1 - the carburettor, 2 - a cover of a head of the cylinder block, 3 - an intake manifold, 4 - an intake manifold layer pad, 5 - a cylinder block head, 6 - an exhaust manifold layer pad, 7 - an exhaust manifold, 8 - a layer pad of a reception outlet pipe, 9 - a rear ring gasket of a bent shaft, 10 - a cover of a rear ring gasket of a bent shaft, 11 - a layer pad, 12 - the cylinder block, 13 - a layer pad of a tube of an oil pump suction manifold, 14 - an oil pump suction manifold, 15 - an oil sump, 16 - an oil pan gasket, 17 - a water pump ring gasket, 18 - a water pump, 19 - a front ring gasket of a bent shaft, 20 - a cylinder block front end cover, 21 - a layer pad, 22 - the oil pump, 23 - a layer pad, 24 - a layer pad of a head of the cylinder block, 25 - a technological plug, 26 - a layer pad, 27 - a head front end cover, 28 - a cam shaft ring gasket.

1 - the accumulator, 2 - a rack, 3 - an air filter, 4 - a measuring instrument of a stream of air, 5 - headlights, 6 - resettings, 7 - a cover of an additional headlight, 8 - a hose of ventilation of a crankcase, 9 - a throttle cover, 10 - the switch "kick-down" and an accelerator cable, 11 - the chamber of the raised pressure, 12 - the valve of steering of idle running turns, 13 - the top radiator hose, 14 - oil-jellied a cover, 15 - a tank of the hydraulic booster of a steering, 16 - a sound signal, 17 - the gauge of level of a liquid of a washer, 18 - a windshield washer pump, 19 - a washer reservoir, 20 - the gauge of level of a cooling fluid, 21 - an expansion chamber, 22 - holders of the engine, 23 - a heater hose, 24 - a drive gear of a hydraulic braking system, 25 - a tank for a brake liquid, 26 - the hydraulic accumulator of a braking system, 27 - the block of safety locks, 28 - the window wiper engine, 29 - the heater gear, 30 - a fuel pressure regulator, 31 - a cover of the distributor, 32 - a measuring instrument of level of oil, 33 - a measuring instrument of level of oil in an automatic gear box.

1 - the thermostatically controlled chamber case, 2 - a thermostatically controlled chamber, 3 - a water pump, 4 - a cover of the gear of a gas distribution, 5 - the union of a bypass hose, 6 - an intake manifold, 7 - a persistent plate of a cam shaft, 8 - a cam shaft pinion gear, 9 - a bent shaft pinion gear, 10 - a flywheel, 11 - the bearing, 12 - a rear ring gasket, 13 - an oil pump drive gear, 14 - a main bearer cover, 15 - the oil pump.

1 - a cylinder block head, 2 - inlet valves, 3 - outlet valves, 4 - a layer pad of a head of the cylinder block, 5 - hydraulic pushers of valves, 6 - crackers, 7 - the top plate of a spring, 8 - a spring, 9 - oil-reflective caps, 10 - the bottom plate of a spring, 11 - an inlet valve saddle, 12 - an outlet valve saddle, 13 - bolts of fastening of a cover of bearings of cam shafts, 14 - a hairpin, 15 - a nut, 16 - oil-bulk a plug, 17 - bolts of fastening of a cover of a head of the cylinder block, 18 - a ring gasket of the intensifying barrel, 19 - the intensifying barrel, 20 - a cover gasket of a head of the cylinder block, 21 - a bolt, 22, 23 - a bracket, 24 - a bolt, 25 - a guide pin, 26 - a cover of a head of the cylinder block.

See also:
Engine diagram
Ford Scorpio engine diagram